2014 Mazda 3

[JohnM]

what brand of LED Fog Lights will fit on this model?

my folding mirror malfunctioned last week... i was able to repair the mechanism inside.. poor quality plastics used by Mazda...

mostly are hard fit and so brittle..

Motorized folding mirrors are designed to be replaced not repaired. Swerte if you were still able to repair it.

You can check the fog bulb size in the manual. I got the lowest possible output white bulb just to match the headlights and other LEDs up front.

Sent from my SM-A605G using Tapatalk

[JohnM]

About to close a deal on some rims. Are our stock lug nuts compatible with Rays?

Sent from my SM-A605G using Tapatalk

[travajante]

About to close a deal on some rims. Are our stock lug nuts compatible with Rays?

Sent from my SM-A605G using Tapatalk

Depends w/c model. If exposed, not sunken, stock might work.

Sent from my SM-G970F using Tapatalk

[JohnM]

Depends w/c model. If exposed, not sunken, stock might work.

Sent from my SM-G970F using Tapatalk

Gram Lights. Will most likely need hubcentric rings no?

Sent from my SM-A605G using Tapatalk

[travajante]

Gram Lights. Will most likely need hubcentric rings no?

Sent from my SM-A605G using Tapatalk

Nice. Which GLs? If hub bore's 73.1mm, you can grab a set of 73.1-67.1mm hub rings.
4Pcs Aluminum Centric Spigot Hub Rings Wheel Spacer Set 67.1mm ID To 73.1Mm OD
Good to have....1 less vibration-cause to think about.

Sent from my SM-G970F using Tapatalk

[JohnM]

Hobo 57g. Stock lug nuts were a tight fit but doable. 225/50r17 17x7.5 pcd 43 . Ordering hubcentric rings.

Sent from my SM-A605G using Tapatalk

[dr. d]

Hobo 57g. Stock lug nuts were a tight fit but doable. 225/50 pcd 43. Ordering hubcentric rings.

Sent from my SM-A605G using Tapatalk

... tight fit but doable...???
ka-takot yata yan...

[JohnM]

... tight fit but doable...???
ka-takot yata yan...

Tight fit sa gilid so ayaw nila i-impact dahil tatama sa socket. They tightened it manually. No biggie

[dr. d]

Tight fit sa gilid so ayaw nila i-impact dahil tatama sa socket. They tightened it manually. No biggie

basta kasya regular cross-wrench, ok na yan.
heh heh.

[JohnM]

basta kasya regular cross-wrench, ok na yan.
heh heh.

Yup yup! Was trying to avoid buying new lugnuts.

No rubbing issues so far lock to lock. Will try a full load soon.



Sent from my SM-A605G using Tapatalk

[travajante]

Yup yup! Was trying to avoid buying new lugnuts.

No rubbing issues so far lock to lock. Will try a full load soon.



Sent from my SM-A605G using Tapatalk

Grats!!!!!

Sent from my SM-G970F using Tapatalk

[JohnM]

Grats!!!!!

Thanks bai! Your input has been very invaluable

[travajante]

Thanks bai! Your input has been very invaluable

Yours as well, brother John. Amazed by your patience to get moddin'![emoji4][emoji120]

Sent from my SM-G970F using Tapatalk

[JohnM]

What's the recommended tire pressure for 17s? The door sticker says 36psi for 16s with light load.

Any recommended LED brake bulbs for the 1.5? Preferably Lazada :D

[Archerfish]

What's the recommended tire pressure for 17s? The door sticker says 36psi for 16s with light load.

Any recommended LED brake bulbs for the 1.5? Preferably Lazada :D

Perhaps you should stick with that pressure, or a little higher. You don't want your new wheels to have a few "battle scars". With the stock 19" that came with the '6', I have accepted the fate.
[emoji3]

[JohnM]

Perhaps you should stick with that pressure, or a little higher. You don't want your new wheels to have a few "battle scars". With the stock 19" that came with the '6', I have accepted the fate.
[emoji3]

Scary ang 19s haha. Kasya pa naman sana sa 3.

Strange that our crossover requires 33/32 only. It's one step thicker lang.

Just got a shot of my actual mileage: 41,338 kms for a daily driver bought in 2014


Sent from my SM-A605G using Tapatalk

[Egan101]

Scary ang 19s haha. Kasya pa naman sana sa 3.

Strange that our crossover requires 33/32 only. It's one step thicker lang.

Just got a shot of my actual mileage: 41,338 kms for a daily driver bought in 2014


Sent from my SM-A605G using Tapatalk

Puwede yan 19 kung gugustuhin. Ang tanong - gusto mo ba?

Ok lang naman same yung pressure gamitin between 16s and 17s. Just follow the suggested pressure indicated on the inner portion of the driver side door.

Yung 18s ng XT, 32 lang nga suggested ng Subie. I observed that it is better to raise it to 34 on pure highway driving conditions.


Sent from my iPhone using Tapatalk

[JohnM]

Puwede yan 19 kung gugustuhin. Ang tanong - gusto mo ba?

Ayaw haha. Sa dami ng lubak dito mahirap na.

34 lang ako ngayon. Baka taasan ko rin. Sa 16 kasi ramdam ang bigat ng manibela if the pressure goes below 34.

Hubcentric rings arrived. Hope they fit

[JohnM]

Nice. Which GLs? If hub bore's 73.1mm, you can grab a set of 73.1-67.1mm hub rings.
4Pcs Aluminum Centric Spigot Hub Rings Wheel Spacer Set 67.1mm ID To 73.1Mm OD
Good to have....1 less vibration-cause to think about.

73.1-67.1 hubcentric rings fit perfectly. One less thing to worry about

Mechanic suggested getting 19x1.5 lug nuts for more space around them.

[travajante]

73.1-67.1 hubcentric rings fit perfectly. One less thing to worry about

Mechanic suggested getting 19x1.5 lug nuts for more space around them.

[emoji106]

Sent from my SM-G970F using Tapatalk