2014 Mazda 3

[JohnM]

Magkano kaya to mga sir, estimate? tia

Attachment 36495

Two panels. 5k per panel?

Mukhang pwede mo pa i-wax yan until matanggal ang paint transfer para di masyado masakit sa mata while waiting for the quarantine to be lifted.

[emz14]

Two panels. 5k per panel?

Mukhang pwede mo pa i-wax yan until matanggal ang paint transfer para di masyado masakit sa mata while waiting for the quarantine to be lifted.

Thanks for the advice and estimate sir, balak ko din kasi ipa-ceramic coating na sya kaya sana ganun lang yung cost sabi kasi nung mga friends ko around 18k daw. Thanks

[chiezee]

Mga sir na miss ko yung 80k/ 4th year PMS ko last December and balak ko na sana mag PMS outside ng casa. any idea kung ano mga dapat gawin like change oil / Cabin filter etc? thanks

[yapoy86]

Mga sir na miss ko yung 80k/ 4th year PMS ko last December and balak ko na sana mag PMS outside ng casa. any idea kung ano mga dapat gawin like change oil / Cabin filter etc? thanks

I asked golden isuzu at pasay taft.. they have basic pms package.. worth 11k includes spark plugs oil filter, air filter, cabin filter and motor oil 5w30. They also have mechanics there that can perform the job

At 80k kms do atf change.. maybe flush and fill will do..

Their spark plug set cost 5.5k.. i found a seller at lazada selling the spark plug at 1.5k.. but i doubt its original.. fake spark plugs are everywhere..

Oil filter at 400 and both cabin and air filter at 800. Atf FZ at 900 pesos per liter.

Are the prices same with casa?

[nomad]

Last PMS I had before ECQ with Casa for change oil plus usual checks and brake cleaning only, cost me 8K plus.[emoji38] It is already out of Yojin.

So Golden Isuzu's package already looks good based on that alone. BTW, would you know or they shared the exact NGK Laser Iridiums they use?

Sent from my Mi MIX 2S using Tapatalk

[yapoy86]

Last PMS I had before ECQ with Casa for change oil plus usual checks and brake cleaning only, cost me 8K plus.[emoji38] It is already out of Yojin.

So Golden Isuzu's package already looks good based on that alone. BTW, would you know or they shared the exact NGK Laser Iridiums they use?

Sent from my Mi MIX 2S using Tapatalk

Looks like they use mazda pe5r-18-110 plugs.. i think these are the same with ngk laser iridium

[nomad]

Looks like they use mazda pe5r-18-110 plugs.. i think these are the same with ngk laser iridium

Thanks. If that's the case, it's the NGK ILKAR7L11 equivalent. So the SkyActiv now uses the longer thread sparkplugs compared with the earlier MZR engine wherein I used the shorter thread Iridiums.


Sent from my Mi MIX 2S using Tapatalk

[yapoy86]

Thanks. If that's the case, it's the NGK ILKAR7L11 equivalent. So the SkyActiv now uses the longer thread sparkplugs compared with the earlier MZR engine wherein I used the shorter thread Iridiums.


Sent from my Mi MIX 2S using Tapatalk

How much are those ngk ILKAR7L11?

[travajante]

How much are those ngk ILKAR7L11?

For reference...
Dealership priced FZ at Php650.

[yapoy86]

For reference...
Dealership priced FZ at Php650.

Much cheaper at the dealer for the FZ fluid..

Btw. I saw some reviews regarding fake ngk sold in amazon..

Saw ngk laser iridium at lazada priced around 4.6k for the set of 4..

[Lakwatsero]

At 80k kms do atf change.. maybe flush and fill will do..

Oil filter at 400 and both cabin and air filter at 800. Atf FZ at 900 pesos per liter.

Are the prices same with casa?

900 per liter of ATF FZ. Were you able to check how much with casa? Iirc, skyactiv drive needs close to 8 liters. That's gonna cost 7k plus labor medyo madugo. Pero if intervals are at 80k, not so bad.

[travajante]

900 per liter of ATF FZ. Were you able to check how much with casa? Iirc, skyactiv drive needs close to 8 liters. That's gonna cost 7k plus labor medyo madugo. Pero if intervals are at 80k, not so bad.

8L FZ was what I refreshed for the 1.5 SkyG. FZ fluid was Php650/liter & Php2500 for the FZ01-21-500 filter/strainer, both off the dealership. Did this out of curiosity upon hitting 50k of mixed traffic. Very DIYable. Drain w/ sump removal & filter replacement was 4.2L. Filter was clean & change may have been too early. Did a 2nd drain & fill w/ 3.8L. No noticeable performance & op temp range change(monitored thru Scangauge) felt. The swap may have been too soon for something labeled lifetime. I reckon 80-100k should be about right.
Curiosity satisfied. Mind peace bought.[emoji4]...Oh, dipstick has corresponding 50°C(OBD monitored) tranny temp-fluid level mark. The scangauge came handy.[emoji106]

Sent from my SM-G970F using Tapatalk

[Lakwatsero]

8L FZ was what I refreshed for the 1.5 SkyG. FZ fluid was Php650/liter & Php2500 for the FZ01-21-500 filter/strainer, both off the dealership. Did this out of curiosity upon hitting 50k of mixed traffic. Very DIYable. Drain w/ sump removal & filter replacement was 4.2L. Filter was clean & change may have been too early. Did a 2nd drain & fill w/ 3.8L. No noticeable performance & op temp range change(monitored thru Scangauge) felt. The swap may have been too soon for something labeled lifetime. I reckon 80-100k should be about right.
Curiosity satisfied. Mind peace bought.[emoji4]...Oh, dipstick has corresponding 50°C(OBD monitored) tranny temp-fluid level mark. The scangauge came handy.[emoji106]

Sent from my SM-G970F using Tapatalk

Sounds reasonable. Where'd you source the fluids? Will probably do mine soon, 60k with a lot of highway is early from what I read too, but I feel some hesitation in shifting on low revs.

[travajante]

Sounds reasonable. Where'd you source the fluids? Will probably do mine soon, 60k with a lot of highway is early from what I read too, but I feel some hesitation in shifting on low revs.

Provincial dealership. Promdis don't bite nor slap as hard as northerners, I guess?[emoji848]

Sent from my SM-G970F using Tapatalk

[yapoy86]

Leather seat cleaning



I repeated paint polishing as the polish I used didn't remove water marks... used Mothers rubbing compound. I find it more like a polish than a rubbing compound..



Carpet deep cleaning.. Used my steam cleaner.. some liquid laundry detergent to agitate and loosen dirt.. steam cleaned to penetrate then vacuum clean.. you can see dirty water sucked into the vacuum.

[vinrem]

Leather seat cleaning



I repeated paint polishing as the polish I used didn't remove water marks... used Mothers rubbing compound. I find it more like a polish than a rubbing compound..



Carpet deep cleaning.. Used my steam cleaner.. some liquid laundry detergent to agitate and loosen dirt.. steam cleaned to penetrate then vacuum clean.. you can see dirty water sucked into the vacuum.

Good job sir[emoji106]! na miss ko tuloy Mazda ko [emoji22].

Sent from my ONEPLUS A6003 using Tapatalk

[nomad]

Looks great! I hope I have one of those steam cleaners. I just use Meguiar"s Gold Class Rich Leather Cleaner and Conditioner for my leather interior as it does not leave the oily and shiny finish which I hate.

And I waxed mine last week during the holiday, Collinite 845 really brings out the Soul Red beauty:

Sent from my Mi MIX 2S using Tapatalk

[yapoy86]

Cleaned rear brakes and torqued to spec and cleaned under chassis and wheel well liners.

I dont like the liners.. they are soft and good sound absorber but they also absorb water and trap dirt..



Looks like mazda alabang only emptied brake cleaners during yojin.. scrubbed brake dust on the wheels and the brake calipers..






Cleaned the wheels and torqued to spec

[travajante]

Cleaned rear brakes and torqued to spec and cleaned under chassis and wheel well liners.

I dont like the liners.. they are soft and good sound absorber but they also absorb water and trap dirt..



Looks like mazda alabang only emptied brake cleaners during yojin.. scrubbed brake dust on the wheels and the brake calipers..






Cleaned the wheels and torqued to spec

Good job! What brake lube did you apply? Permatex?

Sent from my SM-G970F using Tapatalk

[yapoy86]

Good job! What brake lube did you apply? Permatex?

Sent from my SM-G970F using Tapatalk

Silicone grease.. forgot the brand but its US made i bought from concorde.. very useful.. need to buy more.. that grease served me very well..

Took me 1.5 day for the whole job. Very tiring to work in 35 deg hot humid day