Honda crv 3rd gen issues please help

[Paengers]

Yes on Facebook messanger search for
Gasper pilapil Jr. And tell him a friend whom he repaired the rack and pinion black crv recommended you. He charged me 5k. However usually with the Rack and pinion, the outer tie rod and rack end also needs replacement or repairs.. So keep a seperate budget for that.

Sir any feedback sa repair done with your crv EPS by gaspar pilapil jr? Thank you

Sent from my SM-G935F using Tapatalk

[Paengers]

Decided to try gaspar pilapil's services. repair of EPS alone will cost you 5k. Had my tie rods and rack ends repaired also, 850 each, total or 4 heads = 3.4k. Replaced the stabilizer links as well, (replacement)2.4k pair. All work done for 10.8k. So far so good.

Sent from my SM-G935F using Tapatalk

[Paengers]

After a week, may noise s left side ng suspension. I suspected it to be the balljoint. Went back to gaspar to have it checked. True enough it was the balljoint. Had it repaired. 900*. Left and right side. Nice quiet ride again!

Sent from my SM-G935F using Tapatalk

[aquaboy]

The mechanic said there are only 3 mounts which needs to be changed. There is no noise or any sort of cluck when driving on rough roads. It's super quiet. But on idle with air con, there is vibration. And also sometimes on reverse gear

Sir Szekan, naayos na po ba ung vibration issue nyo?

[joepaps52]

hi guys, 1 week is gone and i am still repairing my car. at the start of this thread, my car had 3 problems...
1) knocking noise from under the car
2) transmission jerk and delay shifting
3) low idle rpm

so far work conducted

1) changed the following parts

LH engine mount
RH engine mount
Rear transmission mount
2 x KYB front shocker
1 x strut mount bearing
2 x stabilizer link
plus labor

31,000 peso

rebushing of rack and pinion
rack end and tie rod repair
ball joint press
labor

6,500 peso

All knocking noise solved.


2) changed the following
Surplus transmission and changed the damaged gears
8 litre transmission ATF
labor plus home service

30,000 peso

Transmission solved


3) did the following
new spark plugs
cleaned throttle body
cleaned MAF sensor
reset ECU
Reset throttle position

still the car idle is very low.... it is now in the hands of a very qualified technician by the name of Frank De Leon. hopefully he will solve this in his own fashion.... shall update soon

hi where did you bring your crv for transmission repair? can you give me the contact no., problem also with jerking i think its my transmission is already in bad shape.
Thanks

[joepaps52]

hi where did you bring your crv for transmission repair? can you give me the contact no., problem also with jerking i think my transmission is already in bad shape.
Thanks

no jerking now after replacing output shaft speed sensor. hoping its solve the jerking.

[Paengers]

no jerking now after replacing output shaft speed sensor. hoping its solve the jerking.

Good to hear that sir. Where did you get the spare part and had it repaired? Thank you

Sent from my SM-G935F using Tapatalk

[shadow]

Paano umabot nasira ng ganyan transmission ninyo?


Sent from my iPhone using Tapatalk

[joepaps52]

Good to hear that sir. Where did you get the spare part and had it repaired? Thank you

Sent from my SM-G935F using Tapatalk

bought the speed sensor from Honda Tandang Sora. replace it myself.

[joepaps52]

Paano umabot nasira ng ganyan transmission ninyo?


Sent from my iPhone using Tapatalk

akala ko rin transmission na problem but after check with my OBD, fault code lumabas is P0723-02 which is Output Shaft Speed Sensor.