TSCP Strada Mods [continued 2]

[dadz]

WOW!! 559nm! parang V8 na na diesel sir dadz hehe...

so bale it was achieved using yung the chip and boost controller? or chip alone? or may boost controller na yung chip parang all in one? hehe sensya na sir...medyo di parin ako familiar...

Sir the boost controller is only use to regulate the boost with out it mag over boost ang turbo about 35 psi which is not safe for our stock turbo.

The reading and performance is all from the chip the boost controller does not put any additional hp or torque. Pang sakal lang siya nag boost.

The chip is a true performance chip it needs to be tap sa TPS wire and RPm wire nag ECU also the MAP sensor wire will be cut and connected to the chip. It is done that way to get the maximum performance. All plug and play chip is an analog design this chip need to be tuned according to the throttle position in every RPM.

[locoroco777]

ahhh, so parang it controls every aspects para mag coordinate lahat to be put in a state of full potential... I hope I got it right...hehe

with regards naman dun sa boost controller, hehe yun pala yung function nun...kala ko something na nakakapag increase ng boost, its meant to limit pa pala hehe

matanong ko na din sir, for the benefit din nung mga gustong magpakabit para macompare nila..

ano naman ibig sabihin nung analog design for the plug and play sir?

saka ano yung TPs wire?

[dadz]

Analog design Na plug and play are type of racing chip daw - as you know i already installed this chips to my truck and use it. Ito yung mga types na me tuning daw na d folder file and also it show some graph na nag tataas nag commonrail din. But if you will check in side i only have some diodes and others but not really a micro chip to save a access the setting you want.

TPS - Throttle Position System

Our truck have a safe mode when it comes to boost. With out altering the system it will not boost above 15 psi. That is the safe mode no other chip in the Philippines can prove na their boost goes above 15.

[G01]

Very impressive dyno result you have there, sir Dadz. Hoping that my truck will have similar result when it undergoes dyno graphing.


Latest mod that I made are DIY Boost Gauge housing and a base for the Smart Gauge:

Sanding the epoxy resin pieces


Applied primer


Finished with urethane paint


Applied double sided tape


Removed some panels to allow for a clean wiring installation

[G01]

Installation completed





Smart gauge


Boost gauge

[dadz]

Very nice workmanship sir galing mo talaga......................wish i have housing like that.

[G01]

Very nice workmanship sir galing mo talaga......................wish i have housing like that.

I can easily replicate it using fiberglass resin sir. But yours nga pala is right hand drive hehe. If you're really interested in having a gauge housing like this then I have to make a new one for the right side.

[tc327]

http://i20.photobucket.com/albums/b2...s/_DSC1046.jpg
sir GO1 di ka nahihirapan magdrive sa truck mo ang daming gadget sa harapan hehehe joke lang ang galing talaga wala na sigurong impassable sa truck mo

[G01]

http://i20.photobucket.com/albums/b2...s/_DSC1046.jpg
sir GO1 di ka nahihirapan magdrive sa truck mo ang daming gadget sa harapan hehehe joke lang ang galing talaga wala na sigurong impassable sa truck mo

Hehe...hindi naman sir. Galing ako ng Manila kanina. Meron sumabay na Montero Sport na GLS SE sa Mac Arthur Highway. Taka siguro yung owner/driver kung bakit mas mabilis yung Strada ko hehe. Sa Marcos Highway puntang Baguio yung dating third gear lang ngayon 4th gear na.

[ooba99]

Sa Marcos Highway puntang Baguio yung dating third gear lang ngayon 4th gear na.

500+nm torque ba naman. Kung may 5th gear pa yan, siguradong sisiw pa rin. Idol talaga si sir G01 pagdating sa strada mods.

[G01]

500+nm torque ba naman. Kung may 5th gear pa yan, siguradong sisiw pa rin. Idol talaga si sir G01 pagdating sa strada mods.

Doc, yung naka-stock wheels kaya siguro ang 5th gear all the way hehe....

[Spoileddux]

Sir GO1, astig talaga truck mo. Akala ko aircraft na sa dami ng display pero ASTIG talaga. Sana makasakay naman minsan.

[nanofossil]

astig talaga si GO1, matulungan mo rin sana ako sa balak naming cover sa tow hitch receiver ko. i've been searching for a company who can engrave metal but to no avail. project namin ito nina LR at Bigblock. kapag natuloy ito pwede nang mag avail ang mga BOSB's na may tow hitch receiver. I got this idea from the setup of PolPol. Yung Harley Davidson cover nya. President, pwede rin nating gamiting pang fund raising ito. here are the images, sorry mahirap i-3d ang strada natin puro curves kaya humugot na lang ako ng ibang 3d image ng pickup:

[ThePatriarch]

ok na fund raising yan bro! all we need is a good supplier with reasonable rates...

[nanofossil]

ok na fund raising yan bro! all we need is a good supplier with reasonable rates...

ok kung nagkataon marami ang papagawa kina Bigblock at Manong ng mga tow hitch receiver hehehehe.

[flash1919]

hi bosb, need your suggestion... just installed cf sticker on my hood.....should i keep the bug deflector?.............TIA

[G01]

astig talaga si GO1, matulungan mo rin sana ako sa balak naming cover sa tow hitch receiver ko. i've been searching for a company who can engrave metal but to no avail. project namin ito nina LR at Bigblock. kapag natuloy ito pwede nang mag avail ang mga BOSB's na may tow hitch receiver. I got this idea from the setup of PolPol. Yung Harley Davidson cover nya. President, pwede rin nating gamiting pang fund raising ito. here are the images, sorry mahirap i-3d ang strada natin puro curves kaya humugot na lang ako ng ibang 3d image ng pickup:

Hirap niyan pag metal hehe...kailangan ng male and female molds para sa stamping process. Sa China marami gumagawa niyan pero quantity of orders has to be high para maoffset yung cost ng steel molds.

Puede rin cast embossed resin then painted or flat metal sheet tapos lagyan ng logo sticker then apply top coat to protect the sticker.

[ThePatriarch]

ayan nano, may idea na si sir GO1... gawin na yan! hehe

[boksvon]

Analog design Na plug and play are type of racing chip daw - as you know i already installed this chips to my truck and use it. Ito yung mga types na me tuning daw na d folder file and also it show some graph na nag tataas nag commonrail din. But if you will check in side i only have some diodes and others but not really a micro chip to save a access the setting you want.

TPS - Throttle Position System

Our truck have a safe mode when it comes to boost. With out altering the system it will not boost above 15 psi. That is the safe mode no other chip in the Philippines can prove na their boost goes above 15.

sir,
kapag nag install ng boost controller,kailangan pa ba mag install ng air to fuel ratio gauge?tia

[nanofossil]

Hirap niyan pag metal hehe...kailangan ng male and female molds para sa stamping process. Sa China marami gumagawa niyan pero quantity of orders has to be high para maoffset yung cost ng steel molds.

Puede rin cast embossed resin then painted or flat metal sheet tapos lagyan ng logo sticker then apply top coat to protect the sticker.

Ok, naisip ko rin na resin na lang din, i think mas lower ang cost. sir GO1 baka may ma refer kayo na company na pwedeng mag mass produce. i have the dimension and design already.

tp, sama ako sa baguio sa iyo para pagusapan natin ni GO1 ito, hehehe.

ni revise ko lang yung images, na realize ko na di proportion yung bumper sa truck: