2014 Mazda 3

[RG-93]

Good day planning to have my engine oil replaced, can I use 10w30 viscosity for my 2015 skyactiv engine?

Sent from my TA-1041 using Tsikot Forums mobile app

[Youncle]

This should give me hope, i almost gave up on finding that d*mn annoying noise, i hope this solves it, already installed and replaced those rubber insulators on my springs still didn't solved the problem

Sent from my TA-1041 using Tsikot Forums mobile app

I was about to order this pero sold out na. Let me know also sir if you have any leads. Thanks!

Sent from my SM-G935F using Tapatalk

[Youncle]

Good day planning to have my engine oil replaced, can I use 10w30 viscosity for my 2015 skyactiv engine?

Sent from my TA-1041 using Tsikot Forums mobile app

I would still prefer 5W-30 sir.

Sent from my SM-G935F using Tapatalk

[RG-93]

I was about to order this pero sold out na. Let me know also sir if you have any leads. Thanks!

Sent from my SM-G935F using Tapatalk

No problem sir, but have you tested it already and proved it was the culprit? Nilalakasan ko nalang my stereo so I would not hear that noise, i can hear it when the road is uneven, and when starting my car so annoying talaga

Sent from my TA-1041 using Tsikot Forums mobile app

[travajante]

Good day planning to have my engine oil replaced, can I use 10w30 viscosity for my 2015 skyactiv engine?

Sent from my TA-1041 using Tsikot Forums mobile app

ACEA A5/B5 5w-30, sir.

Sent from my SM-G970F using Tapatalk

[Youncle]

No problem sir, but have you tested it already and proved it was the culprit? Nilalakasan ko nalang my stereo so I would not hear that noise, i can hear it when the road is uneven, and when starting my car so annoying talaga

Sent from my TA-1041 using Tsikot Forums mobile app

In my case yes, proven siya sir. What they did was they wrapped the pins with copper foil para di mag rattle yun caliper then re-grease, so far so good naman.

Yours is making noise even just starting the car sir?

Sent from my SM-G935F using Tapatalk

[RG-93]

ACEA A5/B5 5w-30, sir.

Sent from my SM-G970F using Tapatalk

As always thanks sir travs, would it affect the performance of my engine if I use the said oil viscosity (10w30) ?

Sent from my TA-1041 using Tsikot Forums mobile app

[RG-93]

In my case yes, proven siya sir. What they did was they wrapped the pins with copper foil para di mag rattle yun caliper then re-grease, so far so good naman.

Yours is making noise even just starting the car sir?

Sent from my SM-G935F using Tapatalk

Yes sir I think it really has something to do with those pins because you have to step on the brake pedal once you press the push start button I hear the clunk/rattling noise when the engine turns on once it's on idle it disappears

Sent from my TA-1041 using Tsikot Forums mobile app

[Youncle]

Yes sir I think it really has something to do with those pins because you have to step on the brake pedal once you press the push start button I hear the clunk/rattling noise when the engine turns on once it's on idle it disappears

Sent from my TA-1041 using Tsikot Forums mobile app

I see. You can also try the copper foil as a temporary fix. Sabi sakin sa shop sir common daw ito sa ibang cars kaya may nakatago sila palagi na copper foil. If may noise ulit after a few months re-grease lang daw and put back the foil.

Sent from my SM-G935F using Tapatalk

[yapoy86]

I just learned that the mazda 3 2014 is already equipped with hill start assist. I thought i have a problem with my brakes coz when i stepped on the brakes on an incline, it was stiff as if it lost vacuum assist.. didn't know that feature..

[yapoy86]

ACEA A5/B5 5w-30, sir.

Sent from my SM-G970F using Tapatalk

Sir travs, how about kixx oils? They have 5w30 fully synthetic oils that are api sn ilsac gf-5 certified.. just dont know if they are acea a5/b5 too

[travajante]

Sir travs, how about kixx oils? They have 5w30 fully synthetic oils that are api sn ilsac gf-5 certified.. just dont know if they are acea a5/b5 too

For Kixx, get this....PAO!


Sent from my SM-G970F using Tapatalk

[yangmen]

Driver side door wont lock fully, yung iba ok naman, but pulling the driver side door handle while the car is locked will unlock the car. Last year, car figured in accident, was sideswiped by delivery truck leading same door being replaced with new one, not sure kung pati yung nasa loob ng door bago din. Pero bago lumabas yung problem, had Mr. Quickie duplicated the door key just for emergency (twice na kasi nalock ang susi sa loob). Then couple of days later pa bago lumabas ang problem. Had asked casa, 2500 daw baklas + diagnosis. M3 1.5 2015 here.

[travajante]

Driver side door wont lock fully, yung iba ok naman, but pulling the driver side door handle while the car is locked will unlock the car. Last year, car figured in accident, was sideswiped by delivery truck leading same door being replaced with new one, not sure kung pati yung nasa loob ng door bago din. Pero bago lumabas yung problem, had Mr. Quickie duplicated the door key just for emergency (twice na kasi nalock ang susi sa loob). Then couple of days later pa bago lumabas ang problem. Had asked casa, 2500 daw baklas + diagnosis. M3 1.5 2015 here.

The door cable connector may not have been re-seated securely into the notch near the door lever. Everything there is mechanical. To check, you'll have to remove the door card. Save your P2500. DIY it using this guide: How to remove take off Front door panel 2013-2018 Mazda 3 - YouTube

- - - - - - - - - - - - - - - - - - - - - -

Driver side door wont lock fully, yung iba ok naman, but pulling the driver side door handle while the car is locked will unlock the car. Last year, car figured in accident, was sideswiped by delivery truck leading same door being replaced with new one, not sure kung pati yung nasa loob ng door bago din. Pero bago lumabas yung problem, had Mr. Quickie duplicated the door key just for emergency (twice na kasi nalock ang susi sa loob). Then couple of days later pa bago lumabas ang problem. Had asked casa, 2500 daw baklas + diagnosis. M3 1.5 2015 here.

The door cable connector may not have been re-seated securely into the notch near the door lever. Everything there is mechanical. To check, you'll have to remove the door card. Save your P2500. DIY it using this guide: How to remove take off Front door panel 2013-2018 Mazda 3 - YouTube

[yangmen]

[QUOTE=travajante;3223066]The door cable connector may not have been re-seated securely into the notch near the door lever. Everything there is mechanical. To check, you'll have to remove the door card. Save your P2500. DIY it using this guide: How to remove take off Front door panel 2013-2018 Mazda 3 - YouTube

- - - - - - - - - - - - - - - - - - - - - -



There seem no problem with the cable connector.



When try push the lock, something pulling it back and then parang may small motor sound like rotating coming from this side of below pic.

[travajante]

[QUOTE=yangmen;3223079]

The door cable connector may not have been re-seated securely into the notch near the door lever. Everything there is mechanical. To check, you'll have to remove the door card. Save your P2500. DIY it using this guide: How to remove take off Front door panel 2013-2018 Mazda 3 - YouTube

- - - - - - - - - - - - - - - - - - - - - -



There seem no problem with the cable connector.



When try push the lock, something pulling it back and then parang may small motor sound like rotating coming from this side of below pic.

Check the actuator cable & terminal connections.

[yangmen]

[QUOTE=travajante;3223085]

Check the actuator cable & terminal connections.

Thanx sir Travs, Im not sure what the problem is, hindi ko matanggal yung actuator coz door lock cylinder is in the way but upon reassembly ok na sya.

Btw, how is door lock cylinder connected to actuator? Is it by gear or something? coz cant find any and physical key cant lock/unlock the car anymore.

[travajante]

[QUOTE=yangmen;3223092]

Thanx sir Travs, Im not sure what the problem is, hindi ko matanggal yung actuator coz door lock cylinder is in the way but upon reassembly ok na sya.

Btw, how is door lock cylinder connected to actuator? Is it by gear or something? coz cant find any and physical key cant lock/unlock the car anymore.

Good job! You may have gotten the cable end to properly get seated upon door card removal/reassembly.
The physical key mechanically unlocks the latch via linkage rod. To understand the basics of the automotive door lock system, check this clip:
How Power Door Locks Work - YouTube

[yangmen]

Had my pms recently and as advised did a la carte.

Kindly share where to source & have cabin & air filter replaced aside from Golden Isuzu, preferably Cavite area. Or ok ba yung nasa Lazada? Cheaper than Casa which cost 5k for both.

Also, casa recommended to have the rotor resurfaced which I also skipped. Can someone recommend shop to have it done?

[jojopad]

Had my pms recently and as advised did a la carte.

Also, casa recommended to have the rotor resurfaced which I also skipped. Can someone recommend shop to have it done?

Drive+ at QC provides brake rotor resurfacing services. Haven't availed their services yet but plan to.

Drive+ Car Care Center