Nissan Frontier Navara [continued]

[12vdc]

Saglit lang ireface, pang yosi lang sa machine shop bka pumayag na. Hehe.. Try mo pm si sir oj, parang may bnbenta sya rotors after nya mag upgrade to DBA.

[rzeraus]

Saglit lang ireface, pang yosi lang sa machine shop bka pumayag na. Hehe.. Try mo pm si sir oj, parang may bnbenta sya rotors after nya mag upgrade to DBA.

ok sir 12vdc salamat, nag pm na ako ke sir OJ.

[Wh1stl3r]

ok sir 12vdc salamat, nag pm na ako ke sir OJ.

Oo nga, mura lang dapat yun. Dito binibigyan lang ng pang Jollibug yung magrereface. Mahal na yun.

For the same price (possibly lower) than OEM you can get brand new DBA rotors. Only the shipping makes the cost prohibitive. If 4 people are interested I can order some. My rotors are still ok but I might need to replace them later this year.

Anyone interested in ProVent 150 oil catch cans PM me. I have a couple extra.

[rzeraus]

Oo nga, mura lang dapat yun. Dito binibigyan lang ng pang Jollibug yung magrereface. Mahal na yun.

For the same price (possibly lower) than OEM you can get brand new DBA rotors. Only the shipping makes the cost prohibitive. If 4 people are interested I can order some. My rotors are still ok but I might need to replace them later this year.

Anyone interested in ProVent 150 oil catch cans PM me. I have a couple extra.

Guys here in Samar charge P900.00 per rotor which I think they are over charging.

sir Wh1stl3r, i'm interested in Provent 150 OCC but it's cost might be too costly for me. on DBA rotors have you inquired them if they can send thru LBC (sea cargo) balikbayan box?

[Wh1stl3r]

Guys here in Samar charge P900.00 per rotor which I think they are over charging.

sir Wh1stl3r, i'm interested in Provent 150 OCC but it's cost might be too costly for me. on DBA rotors have you inquired them if they can send thru LBC (sea cargo) balikbayan box?

Provent 150 is cheaper than Provent 200. Also a lot smaller. It's easier to fit inside our cramped engine bay. For me the cost is reasonable, it's just the filter element that needs replacing annually that is a bit pricey. Re: cost I'll have to check my receipts.

Re: DBA rotors we can ship it via sea no problem but it will be expensive if you ship only 1 set.

[Wh1stl3r]

Mga sir kasya po ba sa navara 4x2 ang 265/65r17? Wala po bang rubbing? Kung may rubbing ano maiisuggest nyo? Thank you.

It will fit, but having rubbing will depend on the rims' offset.

[rzeraus]

Sir Wh1stl3r, hindi ba washable yong filter element ng Provent 150?

guys,
The navara 2010-, how many number of bolts the turbo have to manifold flange? I'm just curious.

thank you.

[nalubmis]

pa check mo sir sa casa for scanning malamang spiral cable yan , meron ka pa busina? pwede naman i repair yung cable kung hindi pa malaki ang naputol pag bibili ka aabutin ng 7-8k sa casa

yes sir wala po busina navara namin..saan kaya meron nag rerepair ng cable na yun?

[Wh1stl3r]

Sir Wh1stl3r, hindi ba washable yong filter element ng Provent 150?

guys,
The navara 2010-, how many number of bolts the turbo have to manifold flange? I'm just curious.

thank you.

Hindi washable e. Eto itsura nya:


As for the exh mani to turbo from memory it's 3 bolts, I think.

[Wh1stl3r]

Sir Wh1stl3r, hindi ba washable yong filter element ng Provent 150?

guys,
The navara 2010-, how many number of bolts the turbo have to manifold flange? I'm just curious.

thank you.

Hindi washable e. Eto itsura nya:


As for the exh mani to turbo from memory it's 3 bolts, I think.

*12vdc
Is it really ok to use Matic S spec'd ATF in our a/t? The bottle says Matic S but not Matic J. Matic S supposedly supercedes Matic J but no official info out there. What do you use for the transfer?

[rzeraus]

Hindi washable e. Eto itsura nya:


As for the exh mani to turbo from memory it's 3 bolts, I think.

*12vdc
Is it really ok to use Matic S spec'd ATF in our a/t? The bottle says Matic S but not Matic J. Matic S supposedly supercedes Matic J but no official info out there. What do you use for the transfer?

sir Wh1stl3r,

thanks you very much for all those infos, oil leaks in the joint (rubber hose to the aluminum tube) between the turbo and intercooler and it drip to the engine.

I'm planning to get a turbo from forefrontindustries Australia, a relative can purchase for me and send thru sea cargo.

[12vdc]

Several mos ago was hearing this fanbelt noise and decided to ignore.. Last weekend noise got louder so i decided to check the alternater and thiss what i found..




Yep, busted front bearings

My 33 spline tool did the pulley

[12vdc]

But wait.. It may appear such bearing replacement as cheap



Theyre not.. Ic regulator got damaged, apparently the misaligned shaft sent damaging signal to the regulator..

Cost of oe regulator P7.5k while NewEra brand is around 1.5-2k but not yet available, so left me no choice but to be P5k poorer.

Moral of the story, belts should be quiet as a house mouse..

[rzeraus]

Sir 12vdc, mine has this like metal grinding noise during starting and it will just go away in a minute or two, I hope it's just the alternator pulley.

how about the carbon brush, how much does it cost and where we can get all these parts?
maraming salamat.

[12vdc]

Sir rz, if you have digital voltmeter you could hook it up and check if voltage drops during the noise. If it does, its the oap clutch slipping.

Mine sounded terribly loud and im pretty sure its the bearing. Voltage however on my scangauge doesn't drop but its erratic doesn't stay at 14.1v

Brush is available at suking alt shop pero mhaba pa. Yung slip ring kapag naupod palit daw buong commutator. The ic regulator is rare, only honda got the same part. Alternator assy ksama yung oap is worth P75k sa planta. Exy

[rzeraus]

Sir rz, if you have digital voltmeter you could hook it up and check if voltage drops during the noise. If it does, its the oap clutch slipping.

Mine sounded terribly loud and im pretty sure its the bearing. Voltage however on my scangauge doesn't drop but its erratic doesn't stay at 14.1v

Brush is available at suking alt shop pero mhaba pa. Yung slip ring kapag naupod palit daw buong commutator. The ic regulator is rare, only honda got the same part. Alternator assy ksama yung oap is worth P75k sa planta. Exy

sir 12vdc,
Alternator is so expensive! I have found some second hand Nissan Navara gasoline engine alternator (selling price P3000.00) but ampere rating is only 100 Amp and the pulley is somewhat smaller, approximately 54 mm in diameter and width is a bit small and if I'm not mistaken it has only five grooves.

[Wh1stl3r]

But wait.. It may appear such bearing replacement as cheap



Theyre not.. Ic regulator got damaged, apparently the misaligned shaft sent damaging signal to the regulator..

Cost of oe regulator P7.5k while NewEra brand is around 1.5-2k but not yet available, so left me no choice but to be P5k poorer.

Moral of the story, belts should be quiet as a house mouse..

At least it's brand new again, pwede nang sirain ulit My a/c compressor has been making noises for a while now, just waiting for it to conk out.

Where do you get your supply of Motul ATF? Autoplus quoted me 1.5K/liter. I think I'll just use this:
Castrol Transmax Multivehicle | Castrol Australia | Products | Home

*rzeraus
Are you getting an oem turbo? Or something else?

[rzeraus]

Sir Wh1stl3r,

I'm planning to get a turbo from ForefrontIndustries Australia, I don't know how long the current turbo will last or how bad it is. I'll have it check at Nissan to have a professional opinion.

[12vdc]

At least it's brand new again, pwede nang sirain ulit My a/c compressor has been making noises for a while now, just waiting for it to conk out.

Where do you get your supply of Motul ATF? Autoplus quoted me 1.5K/liter. I think I'll just use this:
Castrol Transmax Multivehicle | Castrol Australia | Products | Home

Have it checked na asap. Learned my lessons the hard way, ginamit kahit may kakaibang sound kaya may na-damage na iba.

I got mine from Denso shop, same lang sila sa autoplus isa lang supplier nila. Not sure with with Matic S backward compatibility with J, but Motul Multi ATF says Matic S,D,J,K. Im using stick BTW with Motul Gear300 for gearbox. How many k's on the odo?

[rzeraus]

sir 12vdc,
can you please give us the bearing number of the alternator.

salamat ulet!