Nissan Frontier Navara [continued]

[12vdc]

Silicone or polybutyl grease for the sliding pin.. Copper grease is for anti squeal-same as silver based grease, should be applied on the shims and backside of pads..

[jay185]

Silicone or polybutyl grease for the sliding pin.. Copper grease is for anti squeal-same as silver based grease, should be applied on the shims and backside of pads..

Parang yung mga stop break squeal ni abro/cyclo?

[jay185]

So pwede yung silicon compound?

[12vdc]

Yup, pwede sa shims pero eventually it will dry up kung madalas babad sa preno dahil sa lower boiling point.

[jay185]

So ano dapat? Ang hirap pala mag hanap ng grease para sa preno

[12vdc]

Silicone or polybutyl grease for the caliper sliding pins(w/ brake fluid contact po ito)

Copper or silver(zinc,tin mix) for external brake mechanism exposed to hi-temp due to friction like brake pads shims/ backside of brake pads- for anti squeal/gailing.

[rzeraus]

Silicone or polybutyl grease for the caliper sliding pins(w/ brake fluid contact po ito)

Copper or silver(zinc,tin mix) for external brake mechanism exposed to hi-temp due to friction like brake pads shims/ backside of brake pads- for anti squeal/gailing.

sir 12vdc, ok ba yong graphite anti-seize compound pang shim?

salamat...

[12vdc]

Ok din po, basta hi temp 250'C and up.

[rzeraus]

Ok din po, basta hi temp 250'C and up.

thank you, mas mataas pala yong temperature ng copper compared to graphite; copper -1093°C and graphite - 482°C and zinc (silver-gray) - 1426°C. http://www.saftlok.com/ssafteze

[Wh1stl3r]

*rzeraus
Koni rear shocks measurements:
fully compressed (bottomed out): 35cm
fully extended (topped out): 52cm
I'll take measurements of the front when I get the time to take the spacers out.

*12vdc
Wow, the intake is nice. No need for a snorkel hehe. Air box looks bigger though. I wonder if the air filter size is the same as the Spain built D40.

The priming bulb doesn't look like it's going to last as long as the old one. Maybe the new fuel filter is a dual type like the one on the Strada? The bracket holding the filter has sharp edges, looks like a job for 1000 grit sandpaper.

- - - - - - - - - - - - - - - - - - - - - -

*rzeraus
Koni rear shocks measurements:
fully compressed (bottomed out): 35cm
fully extended (topped out): 52cm
I'll take measurements of the front when I get the time to take the spacers out.

*12vdc
Wow, the intake is nice. No need for a snorkel hehe. Air box looks bigger though. I wonder if the air filter size is the same as the Spain built D40.

The priming bulb doesn't look like it's going to last as long as the old one. Maybe the new fuel filter is a dual type like the one on the Strada? The bracket holding the filter has sharp edges, looks like a job for 1000 grit sandpaper.

[rpfronty]

ok ba a/c cleaning ng navara sa mga frigid zone?
i hear baklas daw dash?

tia

- - - - - - - - - - - - - - - - - - - - - -

ok ba a/c cleaning ng navara sa mga frigid zone?
i hear baklas daw dash?

tia

[12vdc]

Baklas talaga dash kaya matagal at mahal palinis sir.

[jay185]

Speaking of. San ba murang kumuha ng replacement evaporator

[dr. d]

- - - - - - - - - - - - - - - - - - - - - -

Speaking of. San ba murang kumuha ng replacement evaporator

if the navarra's aircon is anything like the sentra's..
don't settle for cheap replacement.. get the more expensive replacement.
i tried to scrimp.. it didn't cool enough.. i had to buy the more expensive..

[jay185]

- - - - - - - - - - - - - - - - - - - - - -



if the navarra's aircon is anything like the sentra's..
don't settle for cheap replacement.. get the more expensive replacement.
i tried to scrimp.. it didn't cool enough.. i had to buy the more expensive..

Hayyyyyy Nissan.....

[jay185]

Guys mura lang ba mag pa resurface ng rotor disc? San recommended nyo both North and south

[rzeraus]

Guys mura lang ba mag pa resurface ng rotor disc? San recommended nyo both North and south

*jay185,
sir share mo dito kong makahanap ka, magkano at saan...

salamat.

[koji kabuto]

Guys mura lang ba mag pa resurface ng rotor disc? San recommended nyo both North and south

Minerva westgate ( likod ng Total alabang ). Pero dat pa yun. Not sure kung meron pa sila.

[jay185]

Magkano labor nila sa ganon sir?

[koji kabuto]

Magkano labor nila sa ganon sir?

Sobrang tagal na ako last nagpa gawa ng rotors. Pero hundreds lang ang singil nila that time. Pero rotor ang price. Tapos check nila muna kung pwede pa ang kapal.