Toyota Innova Owners & Discussions [continued 3]

[vic2rem]

Mine at 41K+ still has a few hundred or even thousand km before getting to the tread wear indicator. I just decided it was time to replace because 6 years na.

Sent from my GT-N7100 using Tapatalk

33K 3+ years, Rotation every around 10K.

[chitobarba1972]

kasya siya paps. yan na maximum offset na para sa innova natin kung 7" lapad. pero minsan kasi, nasa design ng mags mismo kahit na pasok sa range ng offset. mas mainam kung ittest fit mo. problema lang naman ay yung sa likod o during full turn kung masyadong malapad at pasok ang offset, check mo sa likod kung tatama sa lower shocks

regarding naman sa tire spec of choice, saktong sakto siya, more than 1% larger in circumference lang siya sa stock wheel set ng innova, ibig sabihin, hindi mo na kailangang magpa wheel alignment (toe and camber) para icorrect suspension mo at same pa din reading the speedometer

currently using 18x8 40 offset, 225/45/18 tires

happy wheel hunting sir

many thanks papsy!!!

[garfield_08]

tama ka sa 2nd statement mo sir. one way valve siya. ang tamang connectivity ng oil catch can ay sa pagitan ng PCV to intake manifold.

kahit walang vacuum from intake manifold marerelease pa din blow-by gases from the engine through the PCV, kaso during part load or acceleration, yung vacuum created by the intake manifold sa PCV, mas nakakatulong na matanggal agad blow-by gases sa makina. kung walang vacuum na tutulong, hihintayin pa ng makina na humigit sa atmospheric pressure yung blow-by bago marelease.

dalawa kasi daanan ng blow-by gases ng makina; isa na yung PCV to intake manifold (dito nilalagay OCC), pangalawa yung breather (valve cover to intake tube connection)

Thanks sir for the info. kaso medyo nalito yata ako sa connection set-up ko. Saan mismo yung location ng PCV at ng breather? observation ko kasi isa lang outlet ng blow-by gases, and I'm assuming its the already the PCV valve (rear part ng valve cover with rubber tube connecting to intake tube before the turbo). Dito naka-connect yung OCC ko. Wala ako napansin na breather inlet. If meron, san location nya? My ride is a 2006 D4-D.

TIA.

[innova2013]

Thanks sir for the info. kaso medyo nalito yata ako sa connection set-up ko. Saan mismo yung location ng PCV at ng breather? observation ko kasi isa lang outlet ng blow-by gases, and I'm assuming its the already the PCV valve (rear part ng valve cover with rubber tube connecting to intake tube before the turbo). Dito naka-connect yung OCC ko. Wala ako napansin na breather inlet. If meron, san location nya? My ride is a 2006 D4-D.

TIA.

senior moment ako bigla D4D pala akala ko VVTi.

tama connection ng OCC mo paps.

[garfield_08]

senior moment ako bigla D4D pala akala ko VVTi.

tama connection ng OCC mo paps.

Ok sir. Many thanks.

[1845ers]

hi po,
ask ko lang po kung ano ang mga ginagawa sa 80K PMS? Kasi po ang mahal ng estmate 16K.
thanks po

[Lew_Alcindor]

hi po,
ask ko lang po kung ano ang mga ginagawa sa 80K PMS? Kasi po ang mahal ng estmate 16K.
thanks po

Checkmo owner's manual. Madami na siguro for replacement kaya mahal na.

Sent from my GT-N5100 using Tapatalk 2

[Retz]

^

Haven't reach at that level yet but basically change all fluids and check-up of your car suspension.

[Mile2]

hi po,
ask ko lang po kung ano ang mga ginagawa sa 80K PMS? Kasi po ang mahal ng estmate 16K.
thanks po

what ever is done in 40K PMS, change all fluids and filters

if your car is nearing the end of warranty, better have it done sa gas station, it would cost less than 8K.

[innova2013]

question mga Sir,

How many kilometers does Toyota Service Center recommends to change D4D fuel filter? I read the manual and it is stated just to inspect every 10,000 Kms? No indicated mileage or time when to replace.

Thanks.