HELP: looking for a good talyer

[papadom]

guys tulong naman. pina-check ko pang-ilalim ng rolla '90 ko kasi may tama yung rear crossmember. i brought it to Dallas Motorworks at Timog. they can't do it there, meron daw kailangan hatakin sa may part nung shocks on my left rear side para pumantay ang yung labas ng gulong. kailangan daw dalhin sa talyer. problem is, i don't have a reliable talyer to go to.

any suggestions? i live w/in q.c. area, tandang sora to be exact....

[H1Tman]

guys tulong naman. pina-check ko pang-ilalim ng rolla '90 ko kasi may tama yung rear crossmember. i brought it to Dallas Motorworks at Timog. they can't do it there, meron daw kailangan hatakin sa may part nung shocks on my left rear side para pumantay ang yung labas ng gulong. kailangan daw dalhin sa talyer. problem is, i don't have a reliable talyer to go to.

any suggestions? i live w/in q.c. area, tandang sora to be exact....

Zee? I haven't tried them but there are a lot of good reviews. In fact, when I have the cash na, I'll surely visit them.

[speedyfix]

chassis alignment needs, try mo velocity sa shaw blvd. medyo mahal pero computerized naman sya.

[albert_b]

Tama dalin mo sa Zee sa may Aurora... i-search mo nalang dito sa forum comments about that shop ni Toti ;-)

[albert_b]

na-alala ko tuloy a couple of years ago, dinala ko sa Rapide yung isang lancer ko and they pointed out na may problem na yung crossmember ko sa harap, 15T daw yun!!! :-)) hanep talaga 'no?

[binoy]

pa-PM naman if you know any good talyer..
sa may Las Pinas area..
thanks..

[binoy]

and yung sa aircon na rin..

meron na rin ako nabasa dito pero sa Pasig area e...
sana sa Las Pinas area..

thanks again.

[dx8976]

goodwill sa pinaglabanan.
look for william co.

[RProject]

Try nyo to...

Pit Stop Auto Works
62 Kundiman Street, Paltok, SFDM
Quezon City
Tel. No. 3748653
Cell No. (0910) 2912632
Hanapin nyo si Lalat, magaling na mechaniko to di ka lolokohin, lahat ginagawa
nyan, conversion, engine overhaul basta lahat... sya yung gumawa ng townace ko galing japan... sigurado ka pang di mawawala ang laman ng auto mo kasi may
warehouse sya...

[vinj]

If it involves chassis alignment, Velocity Motors as Speedyfix mentioned.

[papadom]

thanks for the suggestions guys. any idea on how much it would cost me to have this chasis alignment done?

[speedyfix]

chassis alignment is 3500 to check. if you decide to have it done this fee is waived. rates could range from 10-30k depending on how crooked the chassis is and what needs to be replaced.

[1997]

Ano ang cause ng ganitong problem? Para maiwasn mahal pala mag pa align....

[speedyfix]

normally kapag nababanga ka.

pero it can also happen when the car is old and lagi ka nakapark sa di pantay (i.e. one side on the sidewalk and one side on the ground. )

[morrissey_05]

anybody got the address of velocity motors? or directions? been looking for this for awhile na. thanks.

[speedyfix]

they're along shaw blvd. going to kalentong. corner of 9de pebrero.

[mlaconic]

My cousin is planning to go on a buy n sell business....planning to start with 1 car muna to test...any1 here know a good talyer na mura maningil???Paint jobs,tune-ups,etc... QC area din,lapit T.sora if meron..thanks a lot guys!!

[red 65]

RED 65 paintnix Auto Restoration
158 Tandang Sora, Banlat Q.C. (Inside the Compound)
Ask our exact location at P.Y. Hardware near Mindanao Ave. along Tandang Sora

Body Repair & Painting, Custom Painting, Body Allignments, Panel Repairs, Panel Allignment, Auto Detailing, Electrical, Mechanical, Car Audio Set-up, General Upholstery, alot more stuff....

Might be able to help you guys out? good luck on your future projects. we are always open to customizations and project cars. pimp it up! drag it down, DUB? CHoppeD!

Eric (0917-8324321) RED 65

[mike_0197]

Guys,, help rin if somebody know where can I find shop which has a gadjet to
to syncronize servo. according to mechanic only a computerized syncornizer can fix this servo for my ride lancer, para tumama ang timpla ng idling. I'm from cavite city

appreciated you info

[speedyfix]

the servo is mechanical and normally gets the signal from the computer as to when to turn on/off. it's a plug and play affair when you replace it.