Ceramic coating

[ironman06]

Pag tinapatan mo ng hose, mas mabilis mawala yung water dati compared to now. And yes, I'm seeing more sheeting than beading compared nung freshly coated.


I think ATMT lang ang may Pro and Finest Reserve.

I had this issue initially. Paghugas ko sa car, it didnt bead and sheet. I contacted TD, tapos sabi niya, it wont talaga if the car is dirty. That time, naulanan yung kotse and nalagyang ng napakaraming dumi from the tree where it was parked.

True enough after removing the dirt, it beaded and sheeted like it was supposed to do.

So my tip is, if dirty talaga, remove the layer of dirt first. Yung dirt covers the coating below and is the one trapping the water.

[StockEngine]

I had this issue initially. Paghugas ko sa car, it didnt bead and sheet. I contacted TD, tapos sabi niya, it wont talaga if the car is dirty. That time, naulanan yung kotse and nalagyang ng napakaraming dumi from the tree where it was parked.

True enough after removing the dirt, it beaded and sheeted like it was supposed to do.

So my tip is, if dirty talaga, remove the layer of dirt first. Yung dirt covers the coating below and is the one trapping the water.

beading requires the surface to be clean. kinda weird lng na mawala agad yun beading lol

[TheUninvited]

I had this issue initially. Paghugas ko sa car, it didnt bead and sheet. I contacted TD, tapos sabi niya, it wont talaga if the car is dirty. That time, naulanan yung kotse and nalagyang ng napakaraming dumi from the tree where it was parked.

True enough after removing the dirt, it beaded and sheeted like it was supposed to do.

So my tip is, if dirty talaga, remove the layer of dirt first. Yung dirt covers the coating below and is the one trapping the water.

Yeah, that was my assumption but it happens after hand washing and rinsing the car (not dried yet).

I'll probably try to dry it first then hose it down again and try to check the beading.

[Maria Salve]

Yeah, that was my assumption but it happens after hand washing and rinsing the car (not dried yet).

There you go. It was already clean but still no beading. Bottom line, the ceramic coating did not adhere properly to the clear coat after it was applied. I would blame that to the incident that the vehicle was exposed to rain even before the 24-hour curing time.

[zechs]

Yeah, that was my assumption but it happens after hand washing and rinsing the car (not dried yet).

I'll probably try to dry it first then hose it down again and try to check the beading.

As in no beading kahit na hose lang? Mukhang kailangan ulitin.

Ung akin, one week di ko ginamit ung car after I coated it para fully cured na.

Can you post pictures nung sinasabi mo *theuninvted? As in all panels ganun?

[JEMANGALINDAN]

As in no beading kahit na hose lang? Mukhang kailangan ulitin.

Ung akin, one week di ko ginamit ung car after I coated it para fully cured na.

Can you post pictures nung sinasabi mo *theuninvted? As in all panels ganun?

1 week tlga po? any update naman po and kung sino gumawa? TIA


Sent from my iPhone using Tapatalk

[zechs]

1 week tlga po? any update naman po and kung sino gumawa? TIA


Sent from my iPhone using Tapatalk

DIY lang ako sir. I bought my own chemicals from US

*theuninvited,
Cge check mo ulit. Pero sa akin kahit dirty ung lower panels (lower doors and bumpers), nagbe-bead pa din. And to early pa kung mag-decon wash ka ulit.

Cquk 3.0 yan?

Let me know if you want to try out my product hehe it boosts the coating properties bec of Si02 content.

[TheUninvited]

As in no beading kahit na hose lang? Mukhang kailangan ulitin.

Ung akin, one week di ko ginamit ung car after I coated it para fully cured na.

Can you post pictures nung sinasabi mo *theuninvted? As in all panels ganun?

I notice it lang sa mga panels that gets dirtiest the most - most noticeable sa lower part ng driver and passenger doors. Whilst the hood/roof and othe areas are still beading pretty good even if dirty (1 week no wash).

I'll try to dry it then hose it down again. If it sheets, time to take it back to TD, I guess.

There you go. It was already clean but still no beading. Bottom line, the ceramic coating did not adhere properly to the clear coat after it was applied. I would blame that to the incident that the vehicle was exposed to rain even before the 24-hour curing time.

Try ko muna to dry by wiping and hose it down again. Tingin ko may car shampoo pa kase. That's probably masking the beading effect.

I'll definitely post an update here.