Results 41 to 50 of 126
-
September 10th, 2012 08:05 PM #41
it all depends on where you will be using the vehicle more often, kung rektahan o acceleration... pero mas ok ata acceleration, bihira kasi maka over nang 120kph manila roads, even on provincial roads dahil napaka risky...
lage ako sa NLEX, opinion ko lang napapansin ko na mas madami mabibilis na monty keysa forts, takbo ko 120-130kph then madalas meh monty na nasa likod at approaching fast... baka mas mabilis lang magpatakbo drivers ng monty's. haha.
RY, iwan nang eve yung mga shuttles sa north, yung mga grandia pati urvan... hirap na hirap sa winding roads mga shuttle. haha..
sa south naman buses talaga kakulitan doon... rektahan kase eh.. hahaha...
-
September 10th, 2012 08:13 PM #42
-
Tsikot Member Rank 1
- Join Date
- Jul 2009
- Posts
- 4,090
September 10th, 2012 09:20 PM #43bukod siguro sa mas designed sa high rev yung monty(based sa specs), mas aerodynamic siya, which will definitely be a big factor lalo na sa high speed
-
September 10th, 2012 10:23 PM #44
imho kahit 160 ka sa rekta pero pagdating sa kurbada eh baba ka ng 60 e cguradong mahahabulan ka ng syento bente lang ang takbo sa rekta pero pag kurbada e nde bumababa ng 80 or depende sa twist lalo na sa south, kung manual vs auto cgurado matatalo manual, UNLESS marunong ka heel-toe-downshifting, regular ako byahe manila bicol samar, innova vvti auto gamit ko, iniiwanan ako ng prado,forester, kahit BUS especially ang mga ULTRABUS sa straight, pero pag twist na nakakahabol ako dahil sa downshifting + engine break = balance out-in-out enter/exit sa curve tas OVERTAKE pag clear, MASARAP paglaruan ang shifter ng toyota, after 6 yrs na ganito style drive isang beses lang ako nag pa ayos ng cylinder gasket..... dahil palaging high rpm may oil na lumalabas, benta ko na innova pang down montero, break in to sorsogon this week! AND na try konarin fortuner vvti manila/bicol ramdam ang body roll unlike innova, malamang pati montero, taas e, in short nasa driver yan, peace!
-
September 10th, 2012 10:40 PM #45
add ko lang 550 km ang distance mula cainta hangang sa byenan ko sa sorsogon, 55 liters fulltank sagad ang innova vvti, sakto 10km/liter ang consumo mix nayan ang trapik mula calamba hangang lucena, plus hataw pa sa 8hrs na byahe, post ko ang sa montero pag byahe ko bicol
-
-
Verified Tsikot Member
- Join Date
- Jun 2009
- Posts
- 222
September 11th, 2012 12:02 AM #47
Sorry Doc kung masyadong technical. The values shows that 4D56 DI-D valve timing is leading compared to the valve timing of 1KD-FTV (which is lagging). Ayan technical pa rin.
Since MD pala kayo I hope you can relate with these:
Imagine that the piston and cylinder is a syringe. (biggest size is 100ml graduation?)
Imagine that the engine valve is the needle of your syringe (biggest diameter needle is 5G? 10G?).
Let me correspond a bigger diameter needle to a leading valve timing while smaller diameter needle is for a lagging timing.
Lets me exaggerate further Doc. Let say giant syringe na kasya ang 620ml na fluid then kabitan natin ng malaking needle, thin-walled kung meron, pero up to the size lang na once pointing downward ang needle eh kusang tutulo na ang fluid na laman ng syringe pero not immediately drain out ang fluid me mga tira pa kunyari na lagpas kalahati after crossing a regular size operating room. Let say ang syringe sample na ito is referring to the 4D56 DI-D.
Then another giant syringe na kasya ang 750ml na fluid then kabitan ng katamtamang laki ng needle para walang significant leak or dripping when pointing downward ang syringe. Let say ang sample na ito is referring to the 1KD-FTV.
Now na may two sets of syringes na. Kelangan ng dalawang pair ng malaking timba. Isa sa pair ay puno ng tubig at isa eh walang laman.
Let me represent engine torque sa volume ng tubig na kayang eh transfer ng syringe (from 1 timba to another) sa isang cycle o balikan.
Let me represent NET engine power sa kung gaano kabilis matransfer (volume/time) ang tubig sa timba (net kasi considered ang loses like drippings and effort ng magtatransfer)
Para sa low RPM which means low cycle, kailangan sympre paglayuin ang dalawang timba sa magkabilang dulo ng operating room.
During low cycle transferring: Ang syringe representing 4D56, dahil oversize ang kanyang needle (valve) has a natural tendency to drip (leak) at low cycle.
While the syringe representing 1KD-FTV since smaller ang size ng needle, mas complete ang volume ng fluid, no significant dripping (leakage) sa low cycle. At since di naman nagmamadali swabe lang ang pagtulak sa plunger ng syringe to spill-out the fluid.
Para sa high RPM which means faster cycle, pagtabihin ang dalawang timba. Then start transferring as fast as possible. Dyan na ngayon babawi ang syringe na malaki ang needle. Mas madali nya eh suck-in then spill-out ang laman nya na fluid kaya mas malaki volume na matataransfer plus lesser time and lesser effort compared to the one with smaller needle.
In this example, Power is represented in terms of volume/time… lesser time equals more power.
-
-
September 11th, 2012 10:06 AM #49
-
September 11th, 2012 11:22 AM #50
see my pahabol statement above. i mean, i can go on vacation anytime. but my spouse has her...
Traffic!