LANCER Itlog (93-96) Owners - Please Post Here!

[rodetor]

SOHC
Valve lash clearance:
Intake = 0.15mm
Exhaust = 0.25mm
Kadalasan mula sa singkit model at sa itlog model.
Mayruon info label sticker under sa hood.

Sent from my UP+ using Tapatalk

[truckaddict]

could be the valves themselves or engine rattle from low octane gas.
have you tried using different fuel? a higher octane one? lets say from 91 octane to 95 octane?

- - - - - - - - - - - - - - - - - - - - - -



could be the valves themselves or engine rattle from low octane gas.
have you tried using different fuel? a higher octane one? lets say from 91 octane to 95 octane?

Thanks Sir 1D4LV, been using 95 octane XCS sa petron. Will also get the valves checked....thanks sir!!! Will keep you posted.

[truckaddict]

When was the last time na check ang valve clearance? Baka malaki na gap o clearance ng mga valves sa engine mo. And kapag mataas ang gear position mo at wala kapa sa appropriate speed, at nag-accelerate ka magtotope talaga engine mo. Sa mga manual transmission at carb type engine kadalasan nakaka-encounter ng ganyan mga symptoms.

Sent from my UP+ using Tapatalk

I think it was last year when the valves were adjusted. Have an EFI manual transmission....will keep you posted when I get the valves checked. Thanks again!!!

- - - - - - - - - - - - - - - - - - - - - -

SOHC
Valve lash clearance:
Intake = 0.15mm
Exhaust = 0.25mm
Kadalasan mula sa singkit model at sa itlog model.
Mayruon info label sticker under sa hood.

Sent from my UP+ using Tapatalk

Thanks will take note of this

- - - - - - - - - - - - - - - - - - - - - -

SOHC
Valve lash clearance:
Intake = 0.15mm
Exhaust = 0.25mm
Kadalasan mula sa singkit model at sa itlog model.
Mayruon info label sticker under sa hood.

Sent from my UP+ using Tapatalk

Thanks will take note of this

[rodetor]

I think it was last year when the valves were adjusted. Have an EFI manual transmission....will keep you posted when I get the valves checked. Thanks again!!!

- - - - - - - - - - - - - - - - - - - - - -



Thanks will take note of this

- - - - - - - - - - - - - - - - - - - - - -



Thanks will take note of this

EFI model. M/T Lancer.
Tuning up.
Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
>Check and adjust valve clearance to specs.
>Then, set your basic ignition timing to specs., with the correct idle speed.
> idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

Sent from my UP+ using Tapatalk

[truckaddict]

EFI model. M/T Lancer.
Tuning up.
Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
>Check and adjust valve clearance to specs.
>Then, set your basic ignition timing to specs., with the correct idle speed.
> idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

Sent from my UP+ using Tapatalk

A million thanks sir *Rodetor!!! Will follow your instructions regarding checkup!

- - - - - - - - - - - - - - - - - - - - - -

EFI model. M/T Lancer.
Tuning up.
Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
>Check and adjust valve clearance to specs.
>Then, set your basic ignition timing to specs., with the correct idle speed.
> idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

Sent from my UP+ using Tapatalk

A million thanks sir *Rodetor!!! Will follow your instructions regarding checkup!

[khamelionne]

hello po! im a newbie here and a newbie to my lancer itlog too. does anyone know a mechanic here in cebu cityt that specializes our car?

TIA po.

- - - - - - - - - - - - - - - - - - - - - -

hello po! im a newbie here and a newbie to my lancer itlog too. does anyone know a mechanic here in cebu cityt that specializes our car?

TIA po.

[Chinoi]

Gud am * PM mga sir yung itlog ko 95mdl. malau man o malapit pag sinumbong sya namamatayan d naman nag oover heat. bago sya mamatay pag tinatapakan ko yung accelerator pumupugak.tapos ayaw na mag start. tapos 5 mins bago sya mag start uli. TULONG PLSSS

Pa check ignition coil. Dapat 25k ohms ang secondary winding resistance. Check distributor cap carbon rotor contact. Dapat 0 ohm to 300 ohms.

[agentx17]

Newbie here! Proud owner din ng Lancer itlog!

[niro_1262000]

salamat po sa tulong

[Peej007]

Hi, just want to ask your help regarding my "itlog".
The engine stalls when AC and headlights are switch on together.

Dati hindi naman ganun and my battery is still new, just 4 months used.
What do you think is the problem with my "itlog?"

Thank you in advance...hehe