ported vs sealed which do you preffer?

[janus08]

ported vs sealed which do you preffer? ano po ba nag mas maganda?

[the_wildthing]

I'm assuming you're talking about the speaker box.

It depends on your purpose.

[the_noise]

For SQ or clarity, sealed provides faster response and tighter sounding bass, which is clearer.

For SPL or boomboom, ported provides more oomph.

If you're a newbie and/or want a little of both, I recommend an abc/dual chambered ported box.

[scarab]

....kung trunk space din concern mo go for sealed.

[alwayz_yummy]

ask ko na din, magpapacustom oval speaker box na roof mounted, ala CRV-soundcruiser. which is more preferable among the 2?..para din maging parang "subs" ko na din yun...4 or 5 way co-ax na oval gagamitin ko...

add ko nalang din, anung materail, wood w/ felt, wood with fiberglass? or clear fiberglass?

[Mamar]

ported for me para boom boom baby

[ILuvDetailing]

add ko nalang din, anung materail, wood w/ felt, wood with fiberglass? or clear fiberglass?

MDF for me, wood isn't stiff enough.

[buraot]

use MDF for the construction of the box, paps..dami ko na nabasa na ndi maganda pag ordinary wood lang..may mas magandang type pa ata, ung paper board ba tawag dun? mas mahal lang kaysa ordinary MDF board..

[janus08]

tanong ko lang po ilang amperes po ang car battery kc nung tetest ko po yung amplifier na alpine v12 mrv - F705 kinabit ko muna po sa power supply tumogtug nmn po sya then pag ang vol. nya po eh ns 3o'clock na, namamatay po, dahil po ba nasa 3 amperes lang po yung power supply o dahil 300watts n sub ang kinabit ko yung 2 po ano po kaya ang mali ko pasensya na po bago lang po kasi ako dito eh! thanks

[ILuvDetailing]

janus: ilan amplifier mo? puro mrvf 705 ba?

[janus08]

isa lang po sir

[ssaloon]

sealed ako. although it gives less oompf than a ported box, it sounds better on a wider range of low frequencies.

[kabuke0]

sealed ako. although it gives less oompf than a ported box, it sounds better on a wider range of low frequencies.

sir,

what do you mean sounds better on a wider range of low frequencies??
matigas ba ang bass ng sealed??
di ba pag sealed di na kailangan ng amp??

newbie lang...

[toolightz]

sealed ako. although it gives less oompf than a ported box, it sounds better on a wider range of low frequencies.

plus the trunk space
bow!!!

[alwayz_yummy]

so, sealed na lang papagawa ko...may alam kayo suking gawaan, di siya sub box, pero co-ax 6x9 5-way ng pioneer ilalagay ko..ung malinis gumawa,ha? mount ko dun sa rearmost ceiling ko...

[janus08]

sakto lang po ba kung 2 10" targa then yung amp ko po ay v12 1507 tama lang po ba yun?

[ILuvDetailing]

kahit stock na alternator kaya na yan. RMS niyan siguro mga 50W/channel or around 100W bridged. Also Check you gain settings, wag lalagpas sa 1/2 if not baka magoverheat, pag nagoverheat papasok yan sa protect mode mamamatay.

[janus08]

pero sir kaya po kaya nya i drive yung 2 sub n 300watts kahit po hindi nakabridge kc po lalagyan ko pa po yung dalawa ng tweets and seps eh!

[the_noise]

pero sir kaya po kaya nya i drive yung 2 sub n 300watts kahit po hindi nakabridge kc po lalagyan ko pa po yung dalawa ng tweets and seps eh!

Kaya kung sa kaya pero mahina yan. 300 watts yung sub but you'll be feeding it only 50w of power. Baka mas ok pa na 1 sub na lang tapos bridged yung 2 channel.

[Pajerokid29]

pero sir kaya po kaya nya i drive yung 2 sub n 300watts kahit po hindi nakabridge kc po lalagyan ko pa po yung dalawa ng tweets and seps eh!

I suggest bro leave the V12 for the seps, get a mono amp, and ung sub mo ba 300 wrms or 300 max? either way I suggest go for atleast 3/4 ng max rating ng subs mo, and if you're gonna get a mono amp, check the ratings on each of its load settings (2ohm,4ohm, etc) this would depend din sa subs mo, if you have for example two 4ohm single voice coil subs, the wiring option that you can go is either 4ohm or 2ohm, pag dual voice, you can wire it in a way na makaka 1ohm ka, para gamit mo lahat ng power ng amp mo, just make sure na ur amp is stable up to the load ur putting it in (1-ohm stable, 2-ohm stable, etc.)