Best shop in Metro Manila to install lower control arm bushing?

**StockEngine** · January 13th, 2020 09:42 PM

Trav

Meron na ba naka import ng superpro? Polys would last so much longer...

**travajante** · January 13th, 2020 10:08 PM

Originally Posted by StockEngine

Trav

Meron na ba naka import ng superpro? Polys would last so much longer...

I wish, stock sir. Powerflex, SuperPro...these upgrades are ordered online. And yes, they keep everything tight & in place much longer w/ some noise penalty should the lube dry up....A minor quirk I'd gladly live with.

Sent from my SM-G970F using Tapatalk

**travajante** · January 13th, 2020 10:17 PM

Originally Posted by tensazangetsu

Yep sir! originally ang plano ko tlaga yung buong lower arm assembly. Halos maiyak ako nun nung binigay sakin ng casa yung quote halos 40k sya pag casa kasama labor haha.

Haven't check yung engine support pa pero tingin ko meron din replacement yan na makikita. Yun isang next daw na baka need ko palitan sabi ng mechanic(although ok pa naman daw) yung stabilizer link buti nalang nasa 1.9k per piece lang sya sa Golden Isuzu hndi masyado mabigat sa bulsa hehehe.

Don't forget to get an alignment, sir.
A peer's KE is getting a TOTAL refresh of the front suspension (arms/bush/links/joints) & engine mounts....All genuine parts bagged home from the US...to the tune of under $700. Not bad.

Sent from my SM-G970F using Tapatalk

**tensazangetsu** · January 13th, 2020 11:41 PM

Originally Posted by travajante

Don't forget to get an alignment, sir.
A peer's KE is getting a TOTAL refresh of the front suspension (arms/bush/links/joints) & engine mounts....All genuine parts bagged home from the US...to the tune of under $700. Not bad.

Sent from my SM-G970F using Tapatalk

Thanks sir! I'll have my alignment check na din since nagalaw yung lower arm although kanina wala naman sya kabig.

$700 for all those parts not bad! the 2 front lower arm alone cost around 18k to 20k here at PH already.

**travajante** · January 13th, 2020 11:51 PM

Originally Posted by tensazangetsu

Thanks sir! I'll have my alignment check na din since nagalaw yung lower arm although kanina wala naman sya kabig.

$700 for all those parts not bad! the 2 front lower arm alone cost around 18k to 20k here at PH already.

Yeah, there are a coupla fluid-filled mounts, torque arm, etc. Genuine was the preference. 1st refresh after 7yrs. It's gonna be like that Louise Ciccone song about the yet to be touched.[emoji4]
You had some good digging & sharing over here. Thanks for your discoveries, sir![emoji120][emoji106]

Sent from my SM-G970F using Tapatalk

**tensazangetsu** · January 14th, 2020 12:16 AM

Originally Posted by travajante

Yeah, there are a coupla fluid-filled mounts, torque arm, etc. Genuine was the preference. 1st refresh after 7yrs. It's gonna be like that Louise Ciccone song about the yet to be touched.[emoji4]
You had some good digging & sharing over here. Thanks for your discoveries, sir![emoji120][emoji106]

Sent from my SM-G970F using Tapatalk

Anytime sir to our fellow Mazda owners.

**bhybhoy** · January 14th, 2020 01:42 AM

Originally Posted by tensazangetsu

Inorder ko yung bushings sir online sa fitinpart.sg then pina install ko kay Velocity.

Pero sabi nila they also check sa Banawe for parts dun sa ibang client nila.

Sir,
pede po pashare nung part number ng inorder nyo bushing? Same po kase ng problem ng car ko.
2015 Mazda 3 1.5 sedan.
Thanks po.

**tensazangetsu** · January 14th, 2020 02:14 AM

Originally Posted by bhybhoy

Sir,
pede po pashare nung part number ng inorder nyo bushing? Same po kase ng problem ng car ko.
2015 Mazda 3 1.5 sedan.
Thanks po.

Eto sir. Should be the same with my 2015 Mazda 3 2.0 sedan.
If ever much better to have it installed sa Velocity sa Aurora Blvd since they have done it na sa M3 ko but any shop that can press in and press out the bushing will do. Cheers!

Front bushing(small):
BUSH, SUSPENSION JIKIU BH25136 KD35-34-47C,KD35-34-47E

Rear bushing(big): Out of stock na sya sa site pero pwede ka mag pre-order sa last week ng february dadating.
BUSH, SUSPENSION JIKIU BH25237 B6S-34-3B_BH,KD35-34-46A,KD35-34-3H_BH

**bhybhoy** · January 14th, 2020 02:55 AM

Originally Posted by tensazangetsu

Eto sir. Should be the same with my 2015 Mazda 3 2.0 sedan.
If ever much better to have it installed sa Velocity sa Aurora Blvd since they have done it na sa M3 ko but any shop that can press in and press out the bushing will do. Cheers!

Front bushing(small):
BUSH, SUSPENSION JIKIU BH25136 KD35-34-47C,KD35-34-47E

Rear bushing(big): Out of stock na sya sa site pero pwede ka mag pre-order sa last week ng february dadating.
BUSH, SUSPENSION JIKIU BH25237 B6S-34-3B_BH,KD35-34-46A,KD35-34-3H_BH

Thanks sir!

**tensazangetsu** · January 19th, 2020 05:35 AM

Originally Posted by bhybhoy

Thanks sir!

Nakalimutan ko sabihin ninipisan pala ng konting konti ni Velocity yung sa dulo ng control arm nung nikakabit na yung bagong big bushing just to be safe na papasok dun sa butas ng big bushing na saktong sakto lang.

After 1 week of using it so far so good naman, nag improve yung ride and happy naman ako sa new bushings. Cheers!