New and Used Car Talk Reviews Hot Cars Comparison Automotive Community

The Largest Car Forum in the Philippines

Page 229 of 254 FirstFirst ... 129179219225226227228229230231232233239 ... LastLast
Results 2,281 to 2,290 of 2533
  1. Join Date
    Mar 2014
    Posts
    901
    #2281
    SOHC
    Valve lash clearance:
    Intake = 0.15mm
    Exhaust = 0.25mm
    Kadalasan mula sa singkit model at sa itlog model.
    Mayruon info label sticker under sa hood.

    Sent from my UP+ using Tapatalk

  2. Join Date
    Apr 2015
    Posts
    8
    #2282
    Quote Originally Posted by 1D4LV View Post
    could be the valves themselves or engine rattle from low octane gas.
    have you tried using different fuel? a higher octane one? lets say from 91 octane to 95 octane?

    - - - - - - - - - - - - - - - - - - - - - -



    could be the valves themselves or engine rattle from low octane gas.
    have you tried using different fuel? a higher octane one? lets say from 91 octane to 95 octane?
    Thanks Sir 1D4LV, been using 95 octane XCS sa petron. Will also get the valves checked....thanks sir!!! Will keep you posted.

  3. Join Date
    Apr 2015
    Posts
    8
    #2283
    Quote Originally Posted by rodetor View Post
    When was the last time na check ang valve clearance? Baka malaki na gap o clearance ng mga valves sa engine mo. And kapag mataas ang gear position mo at wala kapa sa appropriate speed, at nag-accelerate ka magtotope talaga engine mo. Sa mga manual transmission at carb type engine kadalasan nakaka-encounter ng ganyan mga symptoms.

    Sent from my UP+ using Tapatalk
    I think it was last year when the valves were adjusted. Have an EFI manual transmission....will keep you posted when I get the valves checked. Thanks again!!!

    - - - - - - - - - - - - - - - - - - - - - -

    Quote Originally Posted by rodetor View Post
    SOHC
    Valve lash clearance:
    Intake = 0.15mm
    Exhaust = 0.25mm
    Kadalasan mula sa singkit model at sa itlog model.
    Mayruon info label sticker under sa hood.

    Sent from my UP+ using Tapatalk
    Thanks will take note of this

    - - - - - - - - - - - - - - - - - - - - - -

    Quote Originally Posted by rodetor View Post
    SOHC
    Valve lash clearance:
    Intake = 0.15mm
    Exhaust = 0.25mm
    Kadalasan mula sa singkit model at sa itlog model.
    Mayruon info label sticker under sa hood.

    Sent from my UP+ using Tapatalk
    Thanks will take note of this

  4. Join Date
    Mar 2014
    Posts
    901
    #2284
    Quote Originally Posted by truckaddict View Post
    I think it was last year when the valves were adjusted. Have an EFI manual transmission....will keep you posted when I get the valves checked. Thanks again!!!

    - - - - - - - - - - - - - - - - - - - - - -



    Thanks will take note of this

    - - - - - - - - - - - - - - - - - - - - - -



    Thanks will take note of this
    EFI model. M/T Lancer.
    Tuning up.
    Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
    >Check and adjust valve clearance to specs.
    >Then, set your basic ignition timing to specs., with the correct idle speed.
    > idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

    Sent from my UP+ using Tapatalk

  5. Join Date
    Apr 2015
    Posts
    8
    #2285
    Quote Originally Posted by rodetor View Post
    EFI model. M/T Lancer.
    Tuning up.
    Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
    >Check and adjust valve clearance to specs.
    >Then, set your basic ignition timing to specs., with the correct idle speed.
    > idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

    Sent from my UP+ using Tapatalk
    A million thanks sir *Rodetor!!! Will follow your instructions regarding checkup!

    - - - - - - - - - - - - - - - - - - - - - -

    Quote Originally Posted by rodetor View Post
    EFI model. M/T Lancer.
    Tuning up.
    Condition: Timing Belt is in good shape. Properly aligned with its mating marks in camshaft sprocket and crankshaft.
    >Check and adjust valve clearance to specs.
    >Then, set your basic ignition timing to specs., with the correct idle speed.
    > idle speed is around somewhat 750 ~ 800rpm at normal operating temperature.

    Sent from my UP+ using Tapatalk
    A million thanks sir *Rodetor!!! Will follow your instructions regarding checkup!

  6. Join Date
    Oct 2014
    Posts
    3
    #2286
    hello po! im a newbie here and a newbie to my lancer itlog too. does anyone know a mechanic here in cebu cityt that specializes our car?

    TIA po.

    - - - - - - - - - - - - - - - - - - - - - -

    hello po! im a newbie here and a newbie to my lancer itlog too. does anyone know a mechanic here in cebu cityt that specializes our car?

    TIA po.

  7. Join Date
    Jul 2010
    Posts
    570
    #2287
    Quote Originally Posted by niro_1262000 View Post
    Gud am * PM mga sir yung itlog ko 95mdl. malau man o malapit pag sinumbong sya namamatayan d naman nag oover heat. bago sya mamatay pag tinatapakan ko yung accelerator pumupugak.tapos ayaw na mag start. tapos 5 mins bago sya mag start uli. TULONG PLSSS
    Pa check ignition coil. Dapat 25k ohms ang secondary winding resistance. Check distributor cap carbon rotor contact. Dapat 0 ohm to 300 ohms.
    Attached Thumbnails Attached Thumbnails testing-resitance-internal-ignition-coil.jpg   testing-distributor-cap-rotor-contact.jpg  
    Last edited by Chinoi; July 5th, 2015 at 10:42 PM.

  8. Join Date
    Jul 2015
    Posts
    5
    #2288
    Newbie here! Proud owner din ng Lancer itlog!

  9. Join Date
    Jun 2015
    Posts
    5
    #2289
    salamat po sa tulong

  10. Join Date
    Jul 2015
    Posts
    1
    #2290
    Hi, just want to ask your help regarding my "itlog".
    The engine stalls when AC and headlights are switch on together.

    Dati hindi naman ganun and my battery is still new, just 4 months used.
    What do you think is the problem with my "itlog?"

    Thank you in advance...hehe

LANCER Itlog (93-96) Owners - Please Post Here!