guys i don't know if this is an engine leak pero sabi ng tatay ko
sa makina daw talaga galing yung leak..
hindi masyado makita sa picture kung saan talaga galing kasi nasa ilalim
base on the picture medyo malakas yung tagas :|
pa confirm lang po kung ano talaga yung nag lleak..
The Largest Car Forum in the Philippines
- Forums
- Discussions
- Events
- Community
Results 1 to 11 of 11
-
Tsikoteer
- Join Date
- Aug 2010
- Posts
- 333
January 16th, 2012 11:13 PM #1
-
Tsikot Member Rank 2
- Join Date
- Jun 2005
- Posts
- 3,774
January 18th, 2012 12:07 AM #2pa-engine wash with degreasing ka muna para madali makita san galing ang leak... mahirap makita lalo gag gumagapang lang ang oil towards the lower part ng engine
-
Driven
- Join Date
- Jul 2007
- Posts
- 2,848
January 18th, 2012 12:29 AM #3Thats a lot of oil... Crosswind ba to? or D-max? Skid plate ba yung binagsakan ng langis?
I'm guessing its either Oil seal ng crank shaft pulley (pedeng dukutin...tangal belt,cowl, fan & pulley)
or masama yung collar Gasket sa harap na halfmoon... ibaba yung Oil sump nya... better replace the rear as well sayang yung labor.
Mukhang tuyo naman yung front cover... pero if front cover pwede tightening lang ng me turnilyo...
IMHO
-
Tsikoteer
- Join Date
- Aug 2010
- Posts
- 333
January 18th, 2012 11:09 PM #4thank you mga sir sa reply.. pina engine wash ko muna sabi rin kasi ng mekaniko sa caltex
after 2 days ko daw ipatingin ulit para silipin yung butas.. sana hindi malala hehe
-
Tsikoteer
- Join Date
- Aug 2010
- Posts
- 333
February 7th, 2012 10:39 PM #5
-picture from the internet
guys ano ulit tawag dun sa naka bilog na pula? sabi ng mekaniko dun daw kasi galing yung leak
-
Driven
- Join Date
- Jul 2007
- Posts
- 2,848
February 8th, 2012 01:45 AM #6
Originally Posted by cokezero
-picture from the internet
guys ano ulit tawag dun sa naka bilog na pula? sabi ng mekaniko dun daw kasi galing yung leak
Crankshaft pulley, me gasket na metal ang 4ja1 serving as an Oil seal. Mura lang yan P80 lang yata bili ko. tumagal naman... hehehe
-
UST ENT-HNS
- Join Date
- Oct 2002
- Posts
- 22,658
February 8th, 2012 01:51 AM #7Agree with blue gambit, crankshaft pulley gasket/seal.
Common culprit. hehehe.
http://docotep.multiply.com/
Need an Ambulance? We sell Zic Brand Oils and Lubricants. Please PM me.
-
Tsikoteer
- Join Date
- Aug 2010
- Posts
- 333
February 8th, 2012 02:02 AM #8sir saan kaya pwede ipagawa kasi singil sa akin 1800 pull down pa lang, tapos hindi pa kasama piyesa..
madali lang ba ayusin yan?
-
UST ENT-HNS
- Join Date
- Oct 2002
- Posts
- 22,658
February 8th, 2012 02:24 AM #9Dito sa Q.C. madami gumagawa niyan. Hindi ko lang po sure ang labor cost and baka hindi na convenient sa inyo na dumayo pa dito. Yung parts mura lang, matrabaho lang talaga kasi siya gawin.
http://docotep.multiply.com/
Need an Ambulance? We sell Zic Brand Oils and Lubricants. Please PM me.
-
Tsikoteer
- Join Date
- Aug 2010
- Posts
- 333
February 8th, 2012 02:33 AM #10layo nga sir otep, sige po hanap nalang muna ako ng malapit sa amin.. salamat po! :D
-
Tsikoteer
- Join Date
- May 2009
- Posts
- 1,990
February 8th, 2012 11:08 AM #11ginto na yung P1.8k.....similar procedures lang ginagawa kapag papalitan timing belt. but in your case, pagtanggal ng pulley madudukot na yung seal. no need to remove the timing cover (and t. belts) unlike sa belt driven valvetrains. refer sa sticky thread sa taas kung pano tanggalin yang pulley if you want DIY.hth
Reply With Quote
Originally Posted by cokezero
