AVANZA DIY: Cleaning rusted exhaust pipe

[juanarodriguez]

Hi guys! Recently I noticed rust sa end ng exhaust pipe ni Vanzie...so I decided to clean it...

Before pics:




I used the following items to clean the rusted parts:


Sandpaper - got ung pinaka-fine ang grade
Wire brush
Soap and water
Rags - for drying
Penetrating Oil
A lot of muscle power - better than going to the gym

[juanarodriguez]

After:





I am considering on using McKenic Coloured Rust Preventives meron na ba naka-try nun? http://www.mr-mckenic.com/Products_ME1206.htm

[juanarodriguez]

OT Lang...hehehe i just noticed sa isang photo dito ni vanzie may pusa sa ilalim? loko talaga yung hmmmmpppp 24 hours kaya ang security guard ko

Questions?
1. Should I remove the black thing around the pipe or leave it there?
2. Anong material ba yung ginamit for our exhaust pipe? i need this para macounter check ko dun sa bibilhin ko na protector or something....usually nilalagay naman nila if the product is safe on chrome, stainless steel, etc.
3. safe ba gamitin yung mga rust converters?
4. Is it necessary to apply rust converter before painting the area?
5. Meron bang pwede kong pagdalhan kay vanzie para sila na gagawa nung job? Is there a term used for such service? I would appreciate if you can recommend the store, contact person (yung trustworthy please!) and address.

TIA

[meledson]

Iyong rust converter converts rust into something na di na kakalawangin ulit. After that you can use hi-temp paint para ma protect ang previously rusted parts from further rust.

Kaso you have used penetrating oil, hindi puwedeng ma pintahan kaagad. Have to clean it with soap and water to remove the oil before painting.

I think mayroon bosny hi-temp paint na puwedeng magamit.

BTW, ang tiyaga nyo. Hanga ako.

[juanarodriguez]

Hi Pres thanks! matagal ko ng gustong gawin ito kaya lang nag research muna ng konti para sure...eksakto at kailangan kong marelease yung stress this weekend hehehehe....

somebody told me that some rust converter products may not be go well with some material (nakakabutas daw)??? Well, nakagamit na ako nung TURCO in one of my Destroy-It-Yourself projects at home naging itim nga yung inapplyan good thing and hindi naman nabutas yung microwave hehehe...hanapin ko din yung tira kong high temp paint...malakas amoy nung Turco at nakakasunog ng skin katakot gamitin!

meron akong nakita na Mr. McKenic product which accdg to them turns to a diff color when its time to retouch....http://www.mr-mckenic.com/Products_ME1206.htm... nakita ko na ito sa mga shops about 300-500 pesos but research muna para sure. Meron din akong nakita na ibang product same mfr. cleaner na tapos seals also....hhhhmmm babalikan ko ulit and research on it.

BTW, have u read the result of my engine MIL error?

[meledson]

^^^ Sumagot na po ako. Sorry at nagkaroon kayo ng casa horror story.

[jaspi11]

Hi Pres thanks! matagal ko ng gustong gawin ito kaya lang nag research muna ng konti para sure...eksakto at kailangan kong marelease yung stress this weekend hehehehe....

somebody told me that some rust converter products may not be go well with some material (nakakabutas daw)??? Well, nakagamit na ako nung TURCO in one of my Destroy-It-Yourself projects at home naging itim nga yung inapplyan good thing and hindi naman nabutas yung microwave hehehe...hanapin ko din yung tira kong high temp paint...malakas amoy nung Turco at nakakasunog ng skin katakot gamitin!

meron akong nakita na Mr. McKenic product which accdg to them turns to a diff color when its time to retouch....http://www.mr-mckenic.com/Products_ME1206.htm... nakita ko na ito sa mga shops about 300-500 pesos but research muna para sure. Meron din akong nakita na ibang product same mfr. cleaner na tapos seals also....hhhhmmm babalikan ko ulit and research on it.

BTW, have u read the result of my engine MIL error?

next project ko nga ito kay vanzy...tamang tama mag vacation ako this week...thanks ms Jane for this thread at na-challenge ako....sabi ko si Ms Jane nakaya ako pa kaya

[junlatorre]

OT Lang...hehehe i just noticed sa isang photo dito ni vanzie may pusa sa ilalim? loko talaga yung hmmmmpppp 24 hours kaya ang security guard ko

Questions?
1. Should I remove the black thing around the pipe or leave it there?
2. Anong material ba yung ginamit for our exhaust pipe? i need this para macounter check ko dun sa bibilhin ko na protector or something....usually nilalagay naman nila if the product is safe on chrome, stainless steel, etc.
3. safe ba gamitin yung mga rust converters?
4. Is it necessary to apply rust converter before painting the area?
5. Meron bang pwede kong pagdalhan kay vanzie para sila na gagawa nung job? Is there a term used for such service? I would appreciate if you can recommend the store, contact person (yung trustworthy please!) and address.

TIA

Ate Jane

One thing kasi ang exhaust pipes natin if im not mistaken Galvanized Pipe so talagang prone sa rusty dahil sa halo ng condensation (pag bagong start pansinin nyo me konting tubig lumalabas) then ang carbon monoxide ng makina. Actually di mo na dapat ginamitan ng penetrating oil steel brush or sand paper is enough to remove the rusty around it. Better VHT na hi temp paint ang gamitin mo kasi suitable for exhaust yan it wont burn. pwede silver din para orig ang dating. Di mo na kailangan ang rust converter kasi parang deadskin lang ang kalawang kita mo nun na scrape off mo lumabas ang silvery finish ng galvanized pipe. At isa pa talagang prone na madumihan ang exhaust pipe ni vanzy sa design ng likod natin ang turbulence ng hangin sa ilalim will tend to put dirt sa exhaust pipe mo lalo pag umuulan, pansinin mo ang banda ilalam ng bumper mo madumi din.

pero ayos ang diy mo sistah sunod practisin mo e ang pag jack ng oto at tanggal kabit ng gulong hahaaa.

jun

[juanarodriguez]

Muchas gracias amigos!!!

hehehe hindi pa alam ni prime itong pinag-gagagawa ko kay vanzie...pag nalaman patay ako!!! Almost one week na since I made this project and so far ok pa naman si vanzie...will tell him tomorrow...

Maraming salamat ulit sa nag-appreciate...

[jervic44]

Mam Jane ask ko lang kasi color black na yung under chassis ng avanza mo, pinalagyan mo na ba yan ng rustproofing?

[Tepperz]

nice work maam.. linis pagkakagawa.. hehehe..

[meledson]

Sana magawa ko rin iyan bago ko ikabit ang muffer cutter na order ko kay marfin.

[juanarodriguez]

* puroy

hmmmm meron ako nakita na Mckenic Colour Rust Preventives...nag iiba color nya pag kailangan na ulit re-paint....mamaya pupuntahan ko sa mall tapos post ko dito...parang type ko kung clear paint lang...

* Tepperz

Thanks...I noticed from the pics I missed a few spots mukhang kakailanganin ko ng skateboard to go under vanzie hehehe

Sir Meledson....kaya mo yan sir. It took me less than two hours to complete the job including interruptions from my friendly neighbors....

[junlatorre]

Hi guys! Recently I noticed rust sa end ng exhaust pipe ni Vanzie...so I decided to clean it...

Before pics:




I used the following items to clean the rusted parts:


Sandpaper - got ung pinaka-fine ang grade
Wire brush
Soap and water
Rags - for drying
Penetrating Oil
A lot of muscle power - better than going to the gym

Ate Jane

Parang adult tutbras ang itsura a? hahaaa

[Cherey]

... Hello Ms Jane ,galing ng ginawa mo. bihira kasi katulad mo na gagawa ng ganyan.